Mic Test

Check that your microphone works and that your input level lands where it should. Pick the right device, press Start preview, and watch the level bar move while you speak. The audio is analysed in your browser and never leaves it.

How It Works

1

Allow access and pick a device

2

Speak and watch the meter

3

Adjust gain and retest

Who This Is For

Before a video call

Confirm the app will hear you and that the headset you grabbed is the input the browser uses, not the laptop array.

Fixing a flat signal

When nobody can hear you, walking the permission, device, mute and gain list finds the cause in a couple of minutes.

Recording and streaming

Keep peaks near -12 dBFS so a sudden laugh does not clip, and set a gain you can leave untouched.

Frequently Asked Questions

01Why does the test show silence instead of a quiet room?

A working microphone never produces exact digital zeros, because electronics and room tone always contribute something. Pure silence means the signal is blocked before it reaches the browser: a mute switch, zero input volume, a revoked privacy permission, or an input with nothing attached.

02Can I choose between several microphones?

Yes. Every audio input the operating system exposes to the browser is listed: built-in arrays, webcam mics, USB microphones, headsets and virtual devices. Selecting one here does not change your system default, and the list refreshes automatically when you plug in or remove hardware.

03How do I test my microphone online?

Open the tool, press Start preview and allow microphone access in the browser prompt. Device names appear after permission is granted, so pick the input you want to check from the dropdown and speak in your normal voice. The level bar responds in real time and shows the reading in dB.

04Is the audio recorded or sent anywhere?

No. The stream is analysed frame by frame inside the page and discarded immediately. Nothing is recorded, uploaded or stored, and the microphone is released as soon as you press Stop. No account is needed to run the test.

05What input level should I aim for?

For speech, peaks between -12 and -6 dBFS are the healthy range, with an average around -30 to -20 dBFS. Below -30 dBFS you sound distant, and anything that reaches 0 dBFS is clipping. Raise or lower your input gain until normal speech peaks near -12 dBFS.

06Why is my mic not detected?

The browser only lists audio inputs after you grant permission, so a blocked or dismissed prompt leaves the list empty or generic. Check the padlock icon in the address bar, set the microphone to Allow, then reload the page. A device that is physically unplugged will not appear either.

07What does 0 dB mean on the meter?

0 dBFS is digital full scale, the loudest value the audio system can represent, so every reading sits below it. Hitting the top of the bar means the loudest parts of your voice are being flattened, which sounds harsh and cannot be repaired afterwards. Lower the input gain and retest.

08Why does the meter stay flat while I talk?

A flat meter is almost never a broken microphone. The usual causes are a blocked browser permission, the wrong input device selected in the dropdown, a system-level mute or privacy toggle, a hardware mute switch, or another application holding the device. Check those five in that order.

Perfect For

One setting to tune

The percentage and the dB value point at the same thing, so the only decision left is your input gain.

Private by design

The audio is analysed in the tab and discarded, so no voice sample leaves your machine or lands on a server.

Know before the call

Thirty seconds at the meter beats discovering a muted microphone while everyone waits for you to speak.

Key Terms

Gain
The amplification applied to the raw microphone signal, which sets where your voice sits on the meter.
RMS
Root mean square, the average energy of a block of samples, which follows perceived loudness more closely than a single peak.
Peak
The loudest individual sample in a block, which spikes on plosives and sharp sounds.

Why Use This Tool

✓

Nothing leaves the browser

Audio is analysed locally and discarded frame by frame, with no recording, upload or account required.

✓

Device picker

Every audio input exposed to the browser is listed, so you can test the headset instead of the laptop array.

✓

RMS-based measurement

The meter works from the root mean square of 1024 samples, which tracks perceived loudness better than a raw peak.

1024samples analysed per frame
3 stypical time to a moving meter
1 decimalprecision of the dB readout